Sou Influenciador Sou Anunciante
Sou Influenciador Sou Anunciante

Lilly Schwartz YouTube Channel Analytics and Report

Lilly Schwartz Painel de estatísticas e análises do YouTube (Dados atualizados em 2020-03-23)
Entrou no YouTube em: 2013-05-18Área: Espanha  Idioma: Inglês 
486  1.04%
Total de Visitas
15.3K  2.4%
Média de visualizações
493  2.49%
Vídeos Totais
Rótulo do Canal
Assinantes Classificação Global
3,492,306th  (Top 33.98%)
Posição do país/área
43,276th  (Top 67.05%)
Vídeos publicados
0  (Mês Recente)
Est. Partner Earning
$ 0-$ 0
Est. Potential Earnings
$ 3.53  (Cada vídeo)
Lilly Schwartz Folha de dados do canal do YouTube 
Lilly Schwartz Dados do histórico de inscritos (Recente 1 ano)
Dica: Como o YouTube mostra apenas os 3 primeiros dígitos do número de inscritos, tem uma ligeira alteração na curva
Lilly Schwartz Exibe dados do histórico (Recente 1 ano)
Lilly Schwartz Comparação diária de dados de subs e visualizações 
7 dias
30 dias
Número de inscritos aumentados nos últimos 7 dias: Número de inscritos aumentados da semana anterior a semana passada:
Lilly Schwartz Projeções Futuras (Próximo 1 ano)
Desempenho médio das interações dos últimos 30 vídeos.
Gráfico de exibições de vídeos
Vídeo mais visto de Lilly Schwartz Canal do YouTube
1.82K Views· 2019-06-28 Data de publicação· 114 Gosto· 33 Comentários

This time I‘m showing you the finishing stages of my DIY WiFi Arduino darkroom timer and RGB enlarger light source. I tell you all about designing the final PCB board for the project and printing an enclosure for the darkroom timer. The finished project also includes the 3D print of a new enlarger head for my Durst M670 that can take a standard lightbulb. I can interface the timer with a WiFi switch to control my regular Durst heads or a LIFX smart bulb in the 3D printed head that can be controlled via WiFi. The 3D printed head connects to the enlarger via the stock M3 screws. If you want to know more about earlier stages of the project you can watch my vlogs here: Also check out this blog post about the first prototype that was made out of RGB strip lights and a cardboard box: Parts used for the final build: Arduino Mega (US) Node MCU ESP8266 wifi chip (US) Waveshare 0.95 OLED display (US) Adafruit 3x4 keypad (US) 3x 10K Linear potentiometers (US) 1x 10K resistor (buy an assorted pack) (US) 1x 6.3mm jack socket (US) 1x guitar foot switch (I use a non-latching Boss) (US) Mega Shield (my own design) LifX RGB Smart bulb (US) Tp link HS-100 Smart plug for use with the regular enlarger head (US) If you’d like to build an Arduino f-stop timer yourself I suggest you check out Brodie Tyrell’s open hardware and open source project: Personally I went with my own code, because I couldn’t find the components Brodie used and integrating different components just became too confusing. If you can find his exact components, no programming is necessary, which is the most difficult part. If you want to program it yourself, do yourself a favour and use an Arduino Mega from the start. There are no segmentation fault warnings on Arduinos, so if you run out of memory, it will just do random unpredictable stuff, which is a nightmare to debug. And you definitely will run out of memory on a regular Arduino unless you are a wizard at microcontroller memory management! If you want to have a go with my WiFi version and need pointers, contact me directly, I still have some PCB boards too. This is NOT an easy build though and the WiFi bits are not exactly straight forward to set up. You’ll probably find Brodie’s version much easier to build and better documented. Blog posts with further information on my build are coming soon though! Acknowledgements: Thanks to @frak, @196photo and my dad for help along the way! @frak helped with C++ refactoring problems, @196photo prevented the demise of my high power LEDs by pointing out that my LED driver might be unsuitable for them. My dad helped with the earliest stages of the project when I was still trying to figure out RGB strip lights and got a bit stuck with converting from an RGB colour space to RYB colour space. And of course this whole project would have been impossible without the Maker community and open source component libraries for Arduino! Building cool stuff is a community effort! Most importantly: Let’s not forget my husband, who supports me in all my crazy endeavours! Subscribe for more art videos, electronics builds and vlogs: If you enjoy my music, subscribe to my music channel Polarcoaster, where you can listen to it without all the additional fluff: *Recording Equipment* iPad Pro (US) iPhone 5S (US) Gooseneck Tablet Holder (US) ESDDI Ring Light (US) Focusrite Scarlett Solo Studio (US) ✪ Many links I use are affiliate links, so you can support me at no extra cost to you! ✪ Or buy me a roll of film on Ko-fi: *Connect with me* Instagram: Twitter: Facebook:

Vídeo mais visto Lilly Schwartz Canal do YouTube
Distribuição estimada da faixa etária e gênero do público-alvo 
Distribuição estimada geográfica do público-alvo 
Equipe Noxinfluencer

Olá! Qualquer dúvida, por favor deixe-nos uma mensagem e entraremos em contato com você em breve. Tenha um bom dia

Questionando via facebook